Posts Tagged ‘Sweet’

Types of Septic Systems for Boise Homes

Monday, May 14th, 2012

When it comes to septic systems in Boise, there are probably more options than you realize. To a certain extent, the type of septic system installation you choose is determined by the particular conditions around your home. But it is worth learning about the various options so that you can make an informed decision about the kind of system you would like to have.

The more conventional types of septic systems fall into two categories – gravity and pressure distribution. A gravity system, as its name implies, makes use of the force of gravity to drain away waste from your home and into a drainfield.

Gravity systems use gravity to help treat the waste as well, so this type of system requires that you have a particular type of soil and enough space below the ground to allow for proper filtering. If the water table or a layer of hardpan is too close to the ground’s surface around your home, a gravity system may not be an option for you.

Another conventional option is a pressure distribution system. In this setup, a pump regulates the flow of waste from a storage tank to the drainfield. This is the optimal setup if you do not have enough below ground space for a gravity system as the pump makes sure that only the proper amount of waste can enter the drainfield at once and that the waste is distributed evenly when it is pumped in.

There are also several alternative types of septic systems. For instance, mound septic systems are another option to consider when you do not have enough space below ground for a gravity system. In a mound system, the drainfield is actually placed above the surface of the ground and a pump regulates the flow of waste to the field. This allows for adequate treatment before the waste reaches the water table.

Also an option in this type of situation is a sand filter system. This type of septic system incorporates a sand filter holding tank to treat waste before it is allowed out into the drain field. It is another way to make up for the fact that there may not be enough soil to provide adequate filtration but does not require that you build up a mound of earth on your property.  Call Wickstrom Service Company if you would also like to learn more about your septic tank options

Tags: , ,
Posted in Plumbing, septic system installation, Septic Tanks | Comments Off

Murphy Plumber’s Guide: How to Replace a Bathroom Vanity

Wednesday, January 11th, 2012

Because it looks something like a dresser combined with a kitchen counter, you may think of your Murphy home’s bathroom vanity as being a piece of furniture, and therefore that it is simple to replace. Well, there’s good news and bad news there.

The bad news is that because of the sinks and pipes involved, your vanity is part of your plumbing system, so it’s a little trickier than getting a new sofa.

The good news is that it is still something you can do on your own – or at least with a friend – in a few hours or so. After you have measured the space and purchased the new vanity, here is how you can go about replacing the old one:

  1. Shut off the water supply. This is always the first step when undertaking any sort of plumbing work. Put a bucket beneath the sink to catch any water that drips from the supply lines after you disconnect them.
  2. Using a putty or utility knife, loosen the caulk that is sealing the countertop. Gently remove the countertop.
  3. Detach the vanity from the wall. Most vanity units are screwed in place to the wall, so just spot and remove all the screws.
  4. Mark the studs in preparation for positioning the new vanity. Hint: the old one was already drilled into the studs, if it was done properly.
  5. Put the new vanity in place, making sure it is flush to the wall.
  6. Attach the new vanity to the wall, taking care to screw into the wall studs that you marked in step #4.
  7. Put a bead of caulk along the top of the vanity base to hold the countertop in place. Carefully set in the new countertop.
  8. Reconnect the plumbing that you disconnected as part of step #1.
  9. Put down a thin bead of caulk along the edges of the countertop below the lip. Smooth the caulk in place with a damp rag.

Now your new vanity is all set. Allow the caulk to dry before getting moisture near it, and don’t forget to turn the water supply back on! If you run into any problems, don’t hesitate to call your local Murphy plumber!

Tags: , , , , , , ,
Posted in Plumbing | Comments Off

Greenleaf HVAC Tip: The Facts About Indoor Air Quality

Monday, December 19th, 2011

One of the least understood aspects of your Greenleaf home’s comfort system is the indoor air quality. Most people assume that once they have a good furnace and air conditioner installed, there’s nothing left to worry about. However, with the push in the last 20 years to reduce energy loss through poor insulation, most homes are sealed up tighter than ever before. This doesn’t just cause stuffy indoor air – it can actually lead to illness.

How Bad Can Indoor Air Quality Get?

Homes built in the 1980s were recommended to have one third of the ventilation of those built before. Today, the standards have returned to their original levels, but for many years, homes were built with poor ventilation and excessive insulation. The result is a space that holds the air in too well. Everyday contaminants and allergens like dust, pollen, pet dander, mold, or smoke cannot get out of your home and as a result, you can get sick.

In fact, some people even suffer from Sick Building Syndrome (SBS). This is when they feel ill constantly, with respiratory symptoms that have no root cause and are hard to diagnose. Often, it is because they simply breathe too many contaminants and too much stale air.

Fixing Air Quality Is Simple

The first thing needed to fix air quality is a good filtration system. Despite what many people think, simple filtration is not that expensive. There are big, powerful purification systems with advanced ionization units and UV lighting to kill bacteria and viruses, but most families are served well with a simple HEPA filter to remove things like dust, pollen and dander.

It’s a good idea to have your indoor air quality tested, however, just to make sure other contaminants are not present. High humidity can lead to mold growth, and poor ventilation can lead to exhaust or gas fumes in your home. A good carbon monoxide detector is recommended for the latter, but testing should be done to make sure nothing else is floating around.

However you want to fix your indoor air quality issues, know that there are plenty of things you can do with the help of a good filtration device and regular cleanings of your ductwork and vents.

Tags: , , , ,
Posted in Indoor Air Quality | Comments Off

What to Do if Your Heating System Breaks in Harris Ranch

Wednesday, November 30th, 2011

What if the heart of your Harris Ranch home’s heating system – the furnace – stops working? The warm air that used to flow from your vents has been replaced by a chilly draft. It isn’t time to panic, but it is time to take action. Before you do anything, determine why the furnace stopped working. It may be something as simple as a tripped circuit breaker in your electrical panel. Check the circuit breakers first.

The pilot light in your furnace may have blown out. It can be re-lit if you follow the directions in your furnace owner’s manual. You can find answers on how to re-light a pilot light on the Internet, too.

If the shutdown has not been caused by an electrical or pilot light failure, there is still no need to panic. But another obvious question is: did you pay your last gas bill? Maybe you had a shutoff notice and either ignored it or forgot about it.

Now that you are convinced that the furnace has pooped out, here are some things you should do. First, find the name of a qualified heating and cooling professional. If you already use a heating contractor, contact them and schedule a service call.

While you are waiting for help to arrive, ensure that everyone is safe and accounted for. Make sure pets are nearby and protected from the cold, too. What you don’t want to do is use any appliance to keep you warm that is not designed to keep you warm, like a stove. If you have electric space heaters or propane heaters, carefully locate them in a well vented room (windows open a bit or portable fans circulating air). You don’t want any build-up of gases from fossil burning appliances, gases which could contain deadly carbon monoxide.

Huddle up everyone into a room and break out lots of blankets. You may even want to make an “adventure” of this – find a movie to watch and pop up a bunch of popcorn.  If your waiting time is more than 24 hours, you might want to call up a friend or relative and make arrangements to spend the night with them.

The main thing to remember is not to panic. Most qualified heating contractors, knowing the circumstances, will send out a repair person in a matter of minutes or within one or two hours. Just remember to avoid keeping warm by using unvented heating devices.

Tags: , , , , ,
Posted in Heating | Comments Off

How do I Check a Gas Furnace Draft Pressure Switch? A Question from Dry Creek

Wednesday, November 2nd, 2011

There are many reasons why a furnace stops working and in many cases, a Dry Creek homeowner can perform some simple diagnostics to pinpoint the problem. Finding the problem is one thing – fixing it is another. When in doubt, don’t try it yourself. Call a qualified professional.

But let’s look at one possible problem and solution you may be able to perform yourself – testing the draft pressure switch. The draft pressure switch on a gas furnace allows an electrical current to pass through to ignite the furnace. The pressure switch monitors the draft conditions and won’t allow the furnace’s gas valve to open unless draft is correct.

If the switch is malfunctioning, so too will (or will not) the furnace.

The best way to locate the switch is by consulting with your owner’s manual or by going online and simply typing in the words “gas furnace draft switch.” It is identifiable by its round size and is bolted to the outside of the furnace. It should be nearby the draft inducer motor because the two are connected by a metal tube. The tube may sometimes be the culprit, too. A tube that is blocked with condensation may cause the switch to go bad.

To check for proper function, first turn off power to the furnace, either by shutting down the “on’ switch at the furnace or shutting off the circuit breaker.

Use a volt ohm meter to check if the switch is opening and closing properly. Start by zeroing out the meter’s probes by touching the tips together. Using the dial (could be analog or digital), set the meter to 24 volts. Ground the black probe by attaching it to any metal part of the furnace. Then place the end of the red probe on the metal tube connecting the draft pressure switch to the draft inducer motor.

If the switch is working properly the meter should read at least 24 volts, or very near that. If the reading is short of 24 volts, the switch is not working correctly. At that point you may decide to replace it or call a professional to do the task (recommended).

Always remember that there are many sources which will help you diagnose and repair a problem, especially those available through the Internet. If you search YouTube.com you will find many videos advising you on how to repair certain components. Use all of the resources available to you and keep the phone number of a qualified and professional heating and cooling contractor nearby.

Tags: , , , , , ,
Posted in Heating | Comments Off

A Question From Firebird: Why Choose a Programmable Thermostat?

Friday, September 30th, 2011

There are many types of thermostats available for your Firebird home, but which is the best for your particular needs? It depends largely on how often you are home, how many rooms you have and how people in your house use each of those rooms.

A programmable thermostat in particular is a great option because it allows home owners to control when and how much heat or cooling is introduced to their indoor air. Normal thermostats lack this level of control, largely because they are built as simple switches that flip on whenever your temperature gets too low or too high.

Situations for a Programmable Thermostat

When you leave your home every day, you have two options. Either set the heat and AC so you’ll be comfortable when you return, or turn them off completely and suffer through the first half hour or so when you get home that night.

If you choose the former, you’ll pay a lot more in energy bills to heat or cool an empty house. And if your humidity levels need controlling as well, this may be your only option. Those in the second camp are forced to endure uncomfortable temperatures right when they get home and want nothing more than to relax. Not much better.

That’s why so many homeowners are opting for programmable thermostats to overcome this issue. With a programmable model, you can actually tell your home’s comfort system when to turn on and off each day, depending on when people will be there. Imagine going on vacation for three or four days and coming home to a nice and toasty living room and a smaller heating bill to go with it. That’s the kind of control a programmable model offers.

Zone Control and Beyond

Some programmable thermostats even allow you to section your home off into zones and choose specific temperatures for different areas of the house. This allows a great deal more control over when and how your system will operate each day, depending on the individual comfort needs of your family.

If you’re making dinner and don’t want the heat blasting you while you’re standing over the stove, just set the kitchen temperature lower. And with a programmable thermostat, you can tell it to come back on an hour after you leave the kitchen so that it’s comfortable later when you need a glass of water.

Tags: , , , , , ,
Posted in Energy Savings | Comments Off

A Question From Grand View: What Is Geothermal Heating?

Monday, September 26th, 2011

Having a geothermal heating system installed in your Grand View home means that you will actually be able to heat your home with heat extracted from the ground. If this sounds a bit preposterous to you, you are certainly not alone. But this type of home heating does actually work and the technology is not actually that much different from what is used in a standard heat pump system.

Regular heat pumps are able to remove heat from the outdoor air and transfer it into your house to maintain a comfortable temperature in the winter. You may think that there is no heat in the outdoor air in the winter, but that is not actually the case.

Air contains a substantial amount of heat even at very cold temperatures, and heat pumps are able to work quite well, particularly when the outdoor temperature is above freezing. Conveniently, the same process used to heat your house in the winter can be reversed in the summer to extract heat from the indoor air, providing you with a year round home comfort solution.

Geothermal heating works in much the same way, except that geothermal heat pumps extract heat from the ground rather than the air. In order to accomplish this, a loop of pipes is installed in the ground near your house and your geothermal heating system will pump a liquid, generally either antifreeze or water, through those pipes.

As it passes through the pipes, the liquid will absorb heat from the ground and carry it back to a heat exchanger within your house. At that point, the heat from the liquid will be released into air, which is then blown throughout your house.

And just as conventional heat pumps can cool your house in the summer by removing heat and pumping it outside, so too can geothermal heating systems. They do this simply by letting the liquid flowing through the pipes absorb the heat from inside air and then release it into the ground as it travels through the pipe loop below your house.

Because the ground is never as cold in the winter or as hot in the summer as the air, geothermal heat pumps are actually able to work effectively in more extreme conditions than many traditional heat pumps. However, because they require an entire system of pipes to be installed underground, they can be quite a bit more expensive initially as well.

Tags: , , , ,
Posted in Geothermal | Comments Off