Posts Tagged ‘Payette County’

« Older Entries

Repairing Common Boise Sump Pump Problems

Monday, April 2nd, 2012

Your Boise sump pump is an important piece of equipment that pumps out excess groundwater, which prevents flooding hazards in basements and water damage to your home. If the pump stops working or won’t shut off, you can usually solve the issue yourself. During times of heavy rain and potential flooding, it’s best to check your pump on a daily basis to make sure it’s running properly.

You can maintain your pump by having it inspected by a professional Boise plumber, and keeping the pump clean and the well free of debris. Feel free to call Wickstrom Plumbing, Heating & Cooling if you have questions about how to maintain a sump pump, or to make an appointment for an annual inspection and professional cleaning.

Most issues can be repaired easily and without the help of a plumber. Here’s a troubleshooting guide to help you solve minor issues with your pump.

Check for Electrical Problems

Always check to make sure the sump pump is fully plugged in and that there aren’t any fuses that have burned out. If there is standing water in the basement, you should take extra precautions when handling any electrical equipment, even a plug. Call a plumber or electrician for advice if you have any safety concerns.

Check the Float Switch

Just like the float in a toilet tank, the float attached to the side of your sump pump acts as a guide for turning the pump on and off. This is called the float switch, and it usually has a large bulb or other floatation device attached to a metal arm. This float detects the water level inside the well, and it turns the pump on when the water reaches a certain height in the well.

If the pump is plugged in and there are no blown circuits, move the float switch up and down to see if it will turn the pump on. Debris can get trapped underneath the float causing it to stick. If the motor is constantly running, this switch may be stuck in the “on” position if debris is lodged underneath it, or if there’s substantial corrosion.

You can actually move the entire pump around to change the position if there’s no apparent debris causing the issue. Sometimes the pump gets shifted around slightly, and the float switch cannot work properly if the pump isn’t plumb or level. Be careful not to move it too much, since it could damage the drain line attached to the pump motor.

If your motor is constantly running, and none of these steps work, the motor could overheat and stop working. Unplug the pump while you’re investigating the problem, and if none of these steps work, call a professional plumber.

Check for Clogged Filters

In addition to causing issues with the float switch, debris trapped in the screen can also cause the motor to overheat or shut down. If your filter is dirty, try to get out as much of the debris as possible, but if this doesn’t solve the issue, you could have a clogged drain line. In this case, you will need to call a professional plumber to snake out the line.

Preventative Maintenance Tips

You can prevent issues with the sump pump in your Boise home with a few preventative maintenance tasks. Keep debris from falling into the well as much as possible, and clean out any particles that could clog the screen or affect the operation of the float switch. Occasionally inspect the pump and well for any corrosion or other concerns. If you are comfortable with the operation of your pump, drain and clean the entire well and pump at least once a year.

Lastly, call a qualified technician at Wickstrom Plumbing, Heating & Cooling for a yearly sump pump maintenance visit.

 

Tags: , , , ,
Posted in Plumbing | Comments Off

Quail Ridge Plumbing Guide: Causes of Common Plumbing Disasters

Monday, January 9th, 2012

What are some of the costliest repairs in your Quail Ridge home? Costly can be characterized by lost money or lost time – or both. You may have experienced some of these so-called “disasters” and wondered what you could have done to prevent them. In particular, let’s talk about disasters of the wet variety – plumbing problems.

It goes without saying that nothing is built to last. Parts and products will eventually wear out and need to be repaired or replaced. But the rate of repair or replacement has a lot to do with how well things are maintained, especially common plumbing fixtures and appliances in the home. In order to identify some of the disasters caused by plumbing fixtures and appliances, let’s identify the source of the problems – and their location in the home.

We spend a lot of time in the bathroom so let’s start there first. What disasters happen in the bathroom? At least three come to mind: running toilet, leaking shower head, and clogged sink (also found in the kitchen so let’s kill two birds with one stone here). First, the toilet.

A running toilet is annoying and wastes several gallons of water by the hour. It is often caused by a defective flapper inside the tank, not properly sealed and causing water to leak from the tank. Next, the shower head. Leaks often occur when something as simple as a small rubber washer is worn out, breaking the seal and allowing water to leak. Lastly, the clogged sink. The most common culprit of a clogged sink is something that will not decompose or wash away, namely human hair, bits of plastic or fingernails, etc.

All of these bathroom backups can cause extensive water damage to walls or floors. In the most severe cases, a bathroom’s structure can be compromised by something as small as a dripping faucet – if left unchecked over time.

The next place we spend a lot of time is in the kitchen, another prime area for plumbing disasters. Two appliances that drive homeowners nuts (when malfunctioning) are garbage disposals and refrigerator ice makers.

First of all, garbage disposals are not made to dispose of everything. Utensils, plastics, bones and other goodies do not grind up but rather, bind up a disposal. A backed up disposal can shut down the sink drain and spill over its top. Just as annoying is a refrigerator icemaker, which depends on a plastic or copper tube for its water source. A break in the tube or crimp in the copper line can back up the water and cause a major leak behind or below the refrigerator. And like the bathrooms disasters, damaged flooring and walls can be the result.

Maybe the biggest plumbing disaster of all comes from something unseen by the naked eye: frozen water pipes in crawl spaces or attics. Water pipes in uninsulated areas can freeze when outside temperatures fall below the freezing mark. Often, homeowners are unaware of the problem because they are away from the home for extended periods of time or have failed to properly insulate pipes, crawl spaces, or attics. Frozen pipes can burst, causing extensive damage and lead to an even more dangerous situation: mold growth.

How can you avoid common disasters? Make sure your fixtures and appliances are maintained and if needed, serviced by a professional Quail Ridge plumber. You may also want your plumber to give you a whole-house inspection, which can pinpoint potential trouble spots where your next plumbing disaster might be brewing.

Tags: , , , ,
Posted in Plumbing | Comments Off

Huston Heating Repair: How to Fix a Faulty Furnace Blower

Wednesday, January 4th, 2012

The blower fan on your furnace is designed to distribute warm air through the ductwork in your Huston home evenly, ensuring you use all of the energy consumed by your furnace. If the blower doesn’t turn on when the furnace turns on or it continues to run when the furnace is off, it can cost you money and result in cold rooms. Here are some tips on how to fix a faulty furnace blower.

What is the Problem?

First, check to see what the problem is. If your furnace blower remains on all of the time, it may be a thermostat issue. Make sure the fan isn’t set to stay on continuously (a common setting for most air handlers). You should also check the limit control switch to make sure it is working properly. If this is broken, it needs to be replaced which is a relatively simple fix.

If the furnace blower isn’t turning on at all, you may have a belt problem. This can be fixed by you if you have the proper tools. To repair the belt problem, first turn off all electricity to the device. You’ll need to remove the old furnace blower belt, so release the tension in the pulleys before removing the belt.

Installing a new belt is not unlike doing so for your car. Make sure to check the blower or your user manual for proper tension when you install the new belt. Make sure you purchase the right size belt and set it to the right tension. If you cannot or you do not feel comfortable doing so, you should call a professional to inspect and repair the problem for you.

Getting the Blower Back Up and Running

Once your new belt is in place, test the system carefully, starting with the lowest setting (if there are variable settings). If it does not yet work or if something sounds strange, call a Huston technician right away. You don’t want the motor to burn out or something else more substantial to go wrong with your furnace or air handler during the middle of the winter.

Tags: , , , , ,
Posted in Heating | Comments Off

How to Get Your Furnace Ready for Winter in Sunny Slope

Friday, December 9th, 2011

Being cold in the winter is normal – as long as you are outside. But you shouldn’t be cold inside your Sunny Slope home. If that happens, the first place to look to is your furnace, which may not be working correctly. Furnaces are like any other piece of mechanical equipment. They need to be maintained and serviced on a regular basis to ensure they are working at peak efficiency and warming your entire home at your desired comfort level.

First of all, check and see when you last had your furnace serviced. If it has been over one year ago, you should schedule a maintenance inspection from your local qualified heating and cooling professional. And when you make that appointment, ask about service agreements and getting on a regular maintenance schedule. Most heating and cooling contractors offer service agreement plans which include furnace and air conditioning check-ups on an annual basis.

Okay, so you know who to call for maintenance but what can you do yourself? First of all, give your furnace a little “help” by checking the vents and returns throughout the house. Ensure that there are no obstructions or blockages such as rugs, clothing, furniture, etc. You need to have unobstructed paths for your heated and return air to flow. The more congested the path, the harder your furnace will have to work. And while you’re at it, make sure your vents are open or closed, depending on how much you use your rooms. For example, if you have an extra bedroom that doesn’t need to be heated, closed off the vent or close the damper in the ductwork. The heated air will be diverted to other parts of your home where it is needed.

You can also help the airflow by vacuuming the vent cover or removing it and vacuuming any of the ductwork that you can easily get to.

Another maintenance function that you can perform is cleaning or replacing the furnace filter. Depending on the size of your home and its air quality (occupants, pets, etc.), you may want to clean or replace your air filter every one to three months. A dirty filter can restrict airflow and can put contaminants like dirt and dust right back into your air system. If you don’t know how to replace your air filter, consult the furnace owner’s manual or go online to learn more. If your furnace uses an electrostatic air filter, it will need to be removed and cleaned, either by using a hose or with soapy water and a hose. Make sure you let it dry before re-installing it.

You may also want to inspect any electrical wires around your furnace to ensure none are broken or frayed. A visual inspection should be good enough.

Once you have done what you can, let your heating and cooling contractor take over from there. They are licensed and trained to inspect your furnace and ensure that it is in peak operating condition. And do it today – while everyone else is waiting.

Tags: , , , ,
Posted in Heating | Comments Off

A Question from Kuna: What Is AFUE and Why Should I Care?

Monday, December 5th, 2011

If you’ve been shopping for a furnace in Kuna, chances are you’ve noticed that each furnace has its own annual fuel utilization efficiency (AFUE) rating. These generally range from 80% to the high 90% s and the higher the number, the more fuel efficient that particular furnace is.

But what does this number really mean and just how much should you care? Well, the AFUE rating should actually have a significant impact on your furnace purchasing decision, but that doesn’t mean that you’ll always choose the furnace with the highest efficiency rating either.

For one thing, you’ll have to recognize that not every type of furnace is capable of running at the highest efficiency levels. Oil furnaces, for instance, can’t compete with the super high efficiency gas furnaces on the market today. That’s not to say that an oil furnace might not be the best choice for you under certain circumstances, but it does mean that you should take a close look at your furnace usage before you make a decision.

If you do choose a gas furnace, you will of course have the option of getting one that can reach up to 97% or so efficiency. However, that may not always be the best choice either. If you live in a place where with very harsh, long winters and you’re going to be using your furnace heavily, then it’s definitely worth investing in a higher AFUE furnace that can save you considerable amounts on your monthly heating bills.

But if you don’t use your furnace too often as your area has more mild winters it’s probably not worth it for you to invest in such a high efficiency product. That’s because the higher the AFUE of the furnace, the more expensive it is to purchase and install. Certainly you’ll save money every month because you’ll be getting more heat out of the fuel you’re paying for. But if you don’t use your furnace all that much, the savings really won’t be that substantial.

Don’t forget that a furnace with an 80% AFUE rating is still quite energy efficient.

Tags: , , , , ,
Posted in Heating | Comments Off

What Is an Electric Furnace? A Question from Ola

Monday, November 28th, 2011

There are many types of furnaces that you can get for your Ola home that use a variety of energy sources to operate. Gas furnaces use natural or propane gas, boilers and radiators use water, heated by electricity. And then there are electric furnaces, which may have an advantage over other energy sources based on energy costs.

Simply put, electric furnaces function through the use of electricity. They do not require the use of any type of fuel – but function through wires and chords. An electric furnace uses heating coils, sometimes referred to as “resistance calrods” to create heat directly in the air flow. Inside the furnace cabinet are controls, a blower, and the circuit breakers for the heating elements. Some furnaces have the breakers accessible from the outside of the cabinet.

Other add-on accessories may include an electronic air cleaner, air filter, humidifier, high performance media filter, and air conditioning evaporator coil.

The heating process begins with the home’s thermostat. A drop in temperature is sensed by the thermostat, which alerts the electric furnace. The coil then warms up, thanks to the electric current that passes through it. The heated coil in turn heats the temperature of the air around it, which is then blown into the house through a blower. The pressure that is exerted by the blower on the heated air, warms it further. The blower is able to overcome the resistance of the duct work and replace unheated, colder air with the heated air. In most homes there are various return air ducts that are used to bring in the colder air to the furnace. This cold air travels through the furnace, through an air filter, the blower, and finally through the heat exchanger. After this it will then be pushed back into the house as warm air.

To maintain a supply of fresh air in the house, some furnaces also suck air from the atmosphere outside. After the air in the house reaches a particular temperature, the thermostat automatically shuts off the electric furnace.

An electric furnace may be less costly to run, depending on the price of electricity versus other sources like natural gas, propane gas, or oil. Gas and oil are fossil fuels and burning them leaves a “carbon footprint” – the release of carbon compounds and gases into the atmosphere. An electric furnace does not burn fuel and thus does not leave a carbon footprint. This electric warming process results in fewer particulates and contaminants in the air, too.

Tags: , , , , ,
Posted in Heating | Comments Off

How do I Check a Gas Furnace Draft Pressure Switch? A Question from Dry Creek

Wednesday, November 2nd, 2011

There are many reasons why a furnace stops working and in many cases, a Dry Creek homeowner can perform some simple diagnostics to pinpoint the problem. Finding the problem is one thing – fixing it is another. When in doubt, don’t try it yourself. Call a qualified professional.

But let’s look at one possible problem and solution you may be able to perform yourself – testing the draft pressure switch. The draft pressure switch on a gas furnace allows an electrical current to pass through to ignite the furnace. The pressure switch monitors the draft conditions and won’t allow the furnace’s gas valve to open unless draft is correct.

If the switch is malfunctioning, so too will (or will not) the furnace.

The best way to locate the switch is by consulting with your owner’s manual or by going online and simply typing in the words “gas furnace draft switch.” It is identifiable by its round size and is bolted to the outside of the furnace. It should be nearby the draft inducer motor because the two are connected by a metal tube. The tube may sometimes be the culprit, too. A tube that is blocked with condensation may cause the switch to go bad.

To check for proper function, first turn off power to the furnace, either by shutting down the “on’ switch at the furnace or shutting off the circuit breaker.

Use a volt ohm meter to check if the switch is opening and closing properly. Start by zeroing out the meter’s probes by touching the tips together. Using the dial (could be analog or digital), set the meter to 24 volts. Ground the black probe by attaching it to any metal part of the furnace. Then place the end of the red probe on the metal tube connecting the draft pressure switch to the draft inducer motor.

If the switch is working properly the meter should read at least 24 volts, or very near that. If the reading is short of 24 volts, the switch is not working correctly. At that point you may decide to replace it or call a professional to do the task (recommended).

Always remember that there are many sources which will help you diagnose and repair a problem, especially those available through the Internet. If you search YouTube.com you will find many videos advising you on how to repair certain components. Use all of the resources available to you and keep the phone number of a qualified and professional heating and cooling contractor nearby.

Tags: , , , , , ,
Posted in Heating | Comments Off

Poor Boiler Heating Performance (and Happy Halloween Weekend!)

Friday, October 28th, 2011

Happy Halloween weekend from everyone at Wickstrom Plumbing, Heating & Cooling! We hope you have a fantastically spooky time! But you don’t have to be scared if your boiler isn’t working as well as it should, here are some common causes and solutions.

The good thing about boilers is that they are typically reliable and long-lasting. There aren’t a lot of working parts that can break down and cause problems, compared to other home heating equipment. When problems do arise, they are usually related to the expansion tank or circulating pumps. But a problem can be much simpler – like a tripped circuit breaker.

The most common problems can be noise, no heat, or poor/erratic heating. Before calling a qualified heating and cooling professional, take a moment to see if you can figure out the what’s wrong.

If you have a noisy boiler it might be because of two things – a faulty circulating pump or water trapped in the return lines. If the pump breaks it will make a loud noise when its motor runs. Water can be trapped in the return lines, which may require “re-pitching” the lines to allow for a flow back to the boiler. You may be able to adjust the flow by positioning hangers on the piping but replacing a pump is better left to a professional.

If your boiler is producing no heat, it could be because of something as simple as a circuit breaker being tripped or a fuse being blown. Check your circuit breakers and fuse and reset or replace if necessary. Is your boiler thermostat in the heat mode? It should be but if it isn’t, make the switch. If your boiler has a standing pilot you should check to see if it is lit and if not, re-light it.

Other problems would take a professional to fix. For example, no heat can be traced to low water levels in the boiler. The boiler should always be half-full of water and if it isn’t, it is likely because of leaks or a faulty pressure reducing valve. Don’t try and fix the problem by yourself.

Low water levels may not cause the boiler to lose its heating capabilities, but may cause fluctuations in its heating capacity. Again, it is advisable to call a professional to diagnose and fix the problem. Poor heating can also be traced to mineral deposits in the boiler. Consult your owner’s manual on instructions how to flush out the boiler.

As always, read the owner guide or operating manual for your boiler. You should get some good tips on proper maintenance and troubleshooting. And have the phone number of a qualified professional taped to your boiler – just in case.

Tags: , , , , ,
Posted in Heating | Comments Off

The Beauty of Zone Heating: Some Advice From Dry Creek

Wednesday, October 5th, 2011

While it might not technically be a necessity, there are a lot of reasons why you might want to look into having a zone heating system installed in your Dry Creek home. Whether you’ve been using the same home heating system for a long time or are looking to have a new one installed, there’s never a bad time to have a zone heating system put in.

Most people think that the only thing that affects their home heating and cooling bills is the energy efficiency of their furnace or heat pump. However, that’s simply not always the case. Certainly, the more efficient your furnace or heat pump is, the lower your energy bills will be. But that doesn’t mean they’re as low as they could possibly be.

After all, if you don’t have a zone control system installed, you’re paying to heat your entire house every time you turn on the heat. Depending on the size of your house, that could mean you’re heating anywhere from two to 10 rooms or more that are unoccupied at the time. In fact, you could be paying to heat an entire empty wing of your home. And while you’ll pay less than you would if your heating system was less efficient, you’re still paying more than you need to.

With a zone control system, you can heat your home much more efficiently because you can control which areas of the house get the heat and which ones don’t. You can set multiple different temperatures for the different zones of your home, which allows you to keep the occupied areas warm while not forcing you to waste energy to heat unoccupied spaces.

Aside from the economic benefits of only heating the areas of your home that you need, zone control systems also can put an end to some of those contentious thermostat wars that go on in so many households. If the members of your household can never agree on what a comfortable temperature is, they can simply each set their own temperature for their own area of the house.

That way, everyone is happy and no one has to suffer uncomfortably. After all, you paid a lot for your state of the art home heating system. It’s only fitting that you should be able to get the most possible out of it.

Tags: , , , , ,
Posted in Heating | Comments Off

How Much Will a High Efficiency Furnace Save Me? A Question From Boise

Monday, October 3rd, 2011

The furnaces you can buy these days in Boise are all much more energy efficient than those available even 10 years ago. However, that doesn’t mean that all of the current models are created equal. There is still a pretty big variation when it comes to energy efficiency and when it comes to price, so you need to really know what you’re looking for if you want to get the best deal out there.

The first thing you should understand when you’re trying to pick out a furnace is how energy efficiency for this type of equipment it measured. All furnaces come with an annual fuel utilization efficiency (AFUE) rating that reflects just exactly how energy efficient they are.

Any furnace you buy today will have an AFUE of at least 80%, but it’s possible to purchase models with AFUEs of 97% or more. Of course, energy efficiency is generally a good thing, but there are some other things to consider when you’re trying to decide just how energy efficient you need your new furnace to be.

What this calculation really comes down to is how much you’ll be able to save monthly and annually with a higher efficiency furnace. While your heating bills will certainly be lower the higher the furnace’s efficiency is, you will also pay more up front for the highest efficiency models.

This higher purchase price may be worth it, however, if you live in an area with particularly harsh winters. If your heating load is very high and you’ll be using your furnace a lot, your monthly savings will make up for the higher initial price of the high efficiency furnace in a reasonable amount of time.

Tags: , , , , , , ,
Posted in Heating | Comments Off

« Older Entries