Posts Tagged ‘Oreana’

Reasons A Furnace is Producing No Heat Nampa

Friday, March 16th, 2012

The last occasion on which you want to worry about furnace maintenance in Nampa is in the dead of winter, when the outside is chilly you just want to seek refuge in your own toasty home…only to discover that it’s not much warmer than the outdoors.

This may seem like a total emergency, and the combination of chill and frustration may cause panic to set in. Don’t start fretting too much just yet, though. There are some potentially simple causes and solutions for this problem, such as:

  • The thermostat may be set too low or on the wrong setting. Yes, it seems obvious, but sometimes the solution is staring you right in the face. Check that your thermostat is set high enough to call for heat and that it is on HEAT mode.
  • A circuit breaker may be tripped or a fuse may be blown. It could be the one dedicated to the thermostat, glow coil igniter or furnace itself. Check the breaker or fuse box in your home and either flip the breaker or replace the fuse. If it continues to trip or blow, get it looked at professionally—there may be a bigger problem going on.
  • The thermostat may not be working, so it is either improperly detecting the temperature or improperly reporting it to the furnace, so the heat does not kick on. Either way, it probably needs to be replaced.
  • The furnace is not igniting properly. This could mean the pilot light is out on furnaces without electric ignition, the gas valve is closed and can’t ignite or some other ignition malfunction. Check the pilot and gas valves to make sure they are on and working.

If you have checked all these things and the thermostat still is not working, or if you don’t feel comfortable looking into these causes on your own, you are best served by calling a professional repairman to diagnose and fix the furnace.

Often, these big failures are just the symptom of a smaller problem, so in all likelihood you won’t have to replace the furnace or do any major repairs, especially if it has been well-maintained throughout its life.  If you have any questions please call Wickstrom Service Company.

Tags: , ,
Posted in Furnace, Furnace Maintenance, Thermostat | Comments Off

How to Install a Toilet in Boise

Tuesday, February 28th, 2012

A toilet is a relatively basic piece of plumbing equipment in Boise, but that does not mean that installing it is easy. This is certainly a plumbing maintenance that many people can do on their own, but you should be prepared to devoting the majority of your day to the project. While the installation itself is not terribly complicated, it is quite important that you get it right, so make sure you have all of the necessary materials, equipment and tools before you begin.

The first thing to remember is that you need to install your toilet in an appropriate place relative to the rest of your bathroom plumbing. Especially if you are installing your toilet along a branch drain, make sure that the sink, shower and any other plumbing fixtures are upstream of the spot where you will be installing the toilet.

You will also need to make sure that you install the toilet an appropriate distance from the wall. You need to be able to get around the toilet, and you also want to leave space so that work can be performed on the unit later. Putting your toilet too close to the wall can cause all kinds of complications in the way the unit functions and there is also a possibility of condensation build-up. For all of these reasons, it is important to make sure you are allowing an adequate amount of space on all sides.

The procedure you will have to follow when installing a toilet will be slightly different depending on whether you are installing it in a new spot or simply replacing an existing unit. When replacing an old toilet, you need to remove everything involved in the previous installation. That means taking the old bolts out of the floor and scraping away any residue to ensure that you have a clean and even surface to begin your installation on.

You should also make sure that you are aware of all applicable local codes before you begin your work. Even if you technically install your toilet correctly, you could run into trouble later on if your installation is not actually up to code. It is also important to remember to level all of your fixtures before you complete the installation process and to make sure you use a dielectric or brass fitting when attaching galvanized steel and copper to each other.  If you want to follow up with a professional plumbing call Wickstrom Service Company.

Tags: , ,
Posted in Bathroom Plumbing, Plumbing, plumbing maintenance | Comments Off

An Oreana Contractor Tip: Did You Change that Furnace Filter?

Wednesday, December 7th, 2011

No matter what type of furnace you have in your Oreana home, it’s important to remember to change or clean the filter on a regular basis. This is a relatively straightforward process and doesn’t require a heating contractor‘s help. However, if you’re not sure how to go about doing it, you can always have your heating technician demonstrate the process for you on their next regular maintenance visit.

Indeed, changing or cleaning out the furnace filter is an important part of regular furnace maintenance. However, it often needs to be done more than once a year. The specific amount of time that you can go between filter changes depends on many things, but typically it’s good to check on it once every three months or so.

If you have a lot of pets or if anyone in your family has severe allergies, it may be worth it to check and change the filter even more often. Check with the manufacturer to see what their recommendations are as well. Some high performance furnace filters can last up to six months or even a year, but you should still check on the filter periodically to make sure that too much hasn’t built up on it in between replacements or cleanings.

You’ll need to make sure you have the right type of filter to install as a replacement as well. You can get this information from the owner’s manual of your furnace, from the manufacturer or by taking out and examining the current filter in your furnace. Some furnaces also have filters that are meant to be cleaned and then put back in and the cleaning instructions are usually located near the filter itself.

Of course, in order to change your filter you’ll first have to be able to find it. Most of the time, the filter will be located near the blower towards the bottom of the furnace. However, if you’re not having much luck finding it, your owner’s manual should be able to tell you quickly where it is and how to remove it. Before you go to open the chamber and take the filter out, however, be sure you’ve turned off the power to the furnace.

Changing your furnace filter can help improve the air quality in your home and it is also very important when it comes to keeping your furnace running efficiently and effectively. The filters are there to trap airborne particles that can get into the blower and clog it up. When that happens, the performance of your furnace will likely drop and you’ll need to have a professional come out and complete the necessary repairs.

Tags: , , , , ,
Posted in Heating | Comments Off

Propane, Oil or Natural Gas: Which One Should I Choose? A Question from Oreana

Friday, November 11th, 2011

In most cases, you’ll have a choice concerning what type of fuel you’d like your furnace to burn to heat your Oreana home. For most people, this choice comes down to propane, oil or natural gas. The one you choose could significantly impact the cost of heating your home for many years to come, but it’s usually a pretty clear cut decision.

One thing to remember is that most furnaces that burn natural gas can also burn propane. If you don’t yet have a propane tank but are considering getting one, you might not have to make a final decision just yet. Although it’s generally better to set up your furnace for one type of fuel and then leave it that way, you will likely still have the option of converting later on if you should choose to.

If you do have access to natural gas, though, that’s probably going to be your best option. Furnaces that burn natural gas or propane are generally much more efficient than any other type of furnace on the market. You can get them with annual fuel utilization efficiency (AFUE) ratings as low as 80% and as high as 97+%, so that ensures that you’ll be able to find the one to fit your specific situation.

If you’re facing particularly harsh and frigid winters, you’ll want to choose the most energy efficient option available to you and that’s pretty much always going to be a natural gas furnace. Of course, when you’re looking to decide between natural gas and propane as a fuel source, you’ll just want to compare the relative cost for each in your area. For some people natural gas is cheaper, while it’s propane for others. And since your furnace will operate at the same efficiency no matter which of these fuels you choose, you just need to choose the cheapest.

Oil is certainly an option as well, but if you’re looking for a very high efficiency furnace, you’re not going to find one that burns oil. That doesn’t mean that an oil burning furnace might not be a good investment for you. If you don’t have access to natural gas in your area and your heating load isn’t that high, oil might be a perfectly economical choice for you.

Tags: , , , , , , , ,
Posted in Heating | Comments Off

What Are Your Heat Pump Options? A Tip from Nampa

Monday, October 17th, 2011

Once you’ve decided that a heat pump really is the best option for your Nampa home, you’ll still have a lot of options to consider. There are actually quite a few types of heat pumps and they can vary considerably in terms of their energy efficiency and other available features.

For instance, you can choose to go with a heat pump with a one-speed, two-speed or multi-speed compressor. Single speed compressors are only capable of operating at full capacity. That means that they’ll certainly be able to keep your home warm, but they may be working harder than they need to at some points.

A two-speed or multi-speed compressor, on the other hand, can be adjusted to more appropriately fit the heating and cooling needs of the moment. There will certainly be times when you don’t need your heat pump to be going all out, and the ability to regulate this level of performance can benefit you in several ways.

It will allow you to maintain a more consistent indoor temperature to be sure, but it will also reduce the overall wear and tear on your heat pump over time. If your heat pump doesn’t have to run all out all of the time, it simply won’t wear out as fast, and that will save you both money and frustration in the long run. It’s also worth noting that heat pumps with two-speed or multi-speed compressors are more easily integrated into a zone control system if you have one in your home.

However, regardless of what type of compressor your heat pump has, you’ll also have to examine the various heat pump models available to determine what their actual energy efficiency ratings are. Each heat pump actually comes with two ratings, one for heating and one for cooling.

The heating season performance factor (HSPF) reflects the heat pump’s heating efficiency, while the seasonal energy efficiency ratio (SEER) is a measure of its cooling efficiency. The higher both of these numbers are, the higher the efficiency of the unit. But you don’t necessarily need both numbers to be as high as possible to get the best heat pump for your home.

If you’re going to be using the heat pump more for cooling than for heating because of the climate where you live, you’ll want to make sure the unit you get has as high a SEER as possible, but you won’t have to worry too much about the HSPF. But if you’re going to need more heating than cooling, you should pay more attention to the HSPF than the SEER.

Tags: , , , , , ,
Posted in Heat Pumps | Comments Off

What’s the Difference Between a Furnace and a Boiler? A Question From Melba

Friday, October 7th, 2011

When it comes time to choose a new heating system for your Melba home, there is a good chance your choices are limited. Most homes already have either forced air or radiant heat equipment installed so choosing something different would be costly and unnecessary. But, if you have a choice or are moving into a new home, here are some things to consider regarding the difference between furnaces and boilers.

What a Furnace Does

A furnace uses a fuel like gas, oil or electricity to heat a series of coils in the device. The furnace then uses a blower to push air across the heated coil and into an air handler where it can be distributed throughout your home. This is called a forced air system and requires a combination of ducts and filters to keep air moving smoothly and cleanly throughout your home.

If you have access to gas, a gas furnace with an AFUE of 90% or higher is one of the most efficient and cost effective ways to heat your home. These furnaces can also last upwards of 20-25 years with proper maintenance.

What a Boiler Does

A boiler is different in that it uses water as the heat carrying medium, not air. Boilers still need gas, oil or electricity to heat up the water in the system, though they often use less of it than a traditional furnace – depending on the age of the furnace and the boiler. After water is heated in the boiler, your radiant heating system carries the water to baseboard heaters or radiators throughout your home. This form of heat is preferred by many because it doesn’t require ductwork (which requires extra maintenance) or extra air filtering and it is more humidity friendly in a large home.

In terms of efficiency, both boilers and furnaces are efficient if you’re buying a new model. Capacity is also evenly matched. Boilers take the edge in comfort level and if you have the budget, you can install radiant floor heating which allows you to pipe hot water directly into bathroom floors or your living space so that you never again need to walk on cold floors. Another benefit of radiant heating is that the system will hold heat much longer and then release it over time instead of turning on and off a lot as a furnace tends to do.

Tags: , , , , , , ,
Posted in Heating | Comments Off

Green Your Plumbing in Caldwell

Wednesday, September 28th, 2011

These days, “green plumbing” is getting increasing attention in Caldwell.

“Green plumbing” helps the environment by doing one or more of the following:

  • Saving water
  • Saving energy
  • Using environmentally-friendly materials

There are a wide range of green plumbing products that can make a big difference in how much water and energy your home uses. They range from simple accessories that cost less than $20 to major home remodels. Here are a few of them, ranging from the simple and immediate to larger investments with a longer-term payback.

  • Low-flow showerheads and faucet accessories (often called “aerators”). Check the side of your current faucet and showerhead to see if they use more than 1.5 GPM and 2.0 GPM, respectively. If they do, you can benefit from an upgrade. Look for the EPA WaterSense label to be sure that your new showerheads and faucet accessories are water-efficient.
  • Hot water heater blankets and pipe insulation.You don’t need to insulate your hot water heater and  pipes to prevent freezing, but doing it will save money, water, and energy, and (as a bonus) you’ll enjoy hotter showers in the winter. This is a simple DIY job and the materials are extremely affordable.
  • Dual-flush toilets. As the name suggests, these toilets have two different flushes: a “half-flush” for liquid waste, and a “full flush” for solids. Dual-flush toilets are standard in many European countries and are becoming increasingly popular in the U.S. because of their water-saving potential (up to 68% over conventional toilets) and sleek styling.
  • Tankless water heaters. Unlike conventional tank heaters, which use energy constantly to maintain a reserve supply of hot water, tankless heaters only use energy when hot water is needed.  Tankless water heaters are not quite “instantaneous”, as some manufacturers claim, but they provide hot water within a few seconds. Good quality heaters can provide hot water to multiple fixtures simultaneously.

Tags: , , , , ,
Posted in Plumbing | Comments Off

Tips From Collister on Upgrading Your Central Air Conditioner

Wednesday, September 7th, 2011

When the time comes to upgrade the central air conditioner in your Collister home, you will have a lot of things to take into account. If you were generally satisfied with the performance of your old system, it can be very tempting to stick with a similar model. But if you do not examine all of the options out there right now, you may very well be missing out on a great deal.

If you already have a central air conditioner in place, chances are that you also have ductwork throughout your house. In that case, you will probably be better off with a packaged air conditioner as opposed to a split system. If it is a split system you are replacing, however, you should probably keep your search limited to other split systems. Installing a packaged air conditioner when you do not already have ducts in place can dramatically increase the overall cost of the project.

You will also want to make sure that the system you choose is compatible with the heating system and air handler that you already have in place. Most central air conditioning systems can be integrated easily with all types of heating systems, but you should still check to make sure this will not be a problem, particularly if you have an older heating system.

In terms of picking out the right new system for your home, energy efficiency is probably the main factor to consider. While just about every air conditioner on the market right now will be much more efficient than the unit you are replacing, you want to make sure you get a model that will provide you with the optimal savings in the long run.

This does not necessarily mean that you should go out and buy the most energy efficient air conditioner out there. In fact, because the more energy efficient units are also typically more expensive, you may not actually save money by going that route. But you will do well to choose a unit that will save you enough monthly to offset the installation costs and for most people, that means that you will want an air conditioner that is either a SEER 14 or SEER 16.

Of course, the actual amount of money you will save as you move up through the SEER rankings depends on how much you use your air conditioner to begin with. If you live somewhere with very hot weather and you use your unit for a large chunk of the year, it may very well be worth it for you to opt for a very high efficiency model.

Tags: , , , ,
Posted in Air Conditioning | Comments Off