Posts Tagged ‘Middleton’

Murphy Plumber’s Guide: How to Replace a Bathroom Vanity

Wednesday, January 11th, 2012

Because it looks something like a dresser combined with a kitchen counter, you may think of your Murphy home’s bathroom vanity as being a piece of furniture, and therefore that it is simple to replace. Well, there’s good news and bad news there.

The bad news is that because of the sinks and pipes involved, your vanity is part of your plumbing system, so it’s a little trickier than getting a new sofa.

The good news is that it is still something you can do on your own – or at least with a friend – in a few hours or so. After you have measured the space and purchased the new vanity, here is how you can go about replacing the old one:

  1. Shut off the water supply. This is always the first step when undertaking any sort of plumbing work. Put a bucket beneath the sink to catch any water that drips from the supply lines after you disconnect them.
  2. Using a putty or utility knife, loosen the caulk that is sealing the countertop. Gently remove the countertop.
  3. Detach the vanity from the wall. Most vanity units are screwed in place to the wall, so just spot and remove all the screws.
  4. Mark the studs in preparation for positioning the new vanity. Hint: the old one was already drilled into the studs, if it was done properly.
  5. Put the new vanity in place, making sure it is flush to the wall.
  6. Attach the new vanity to the wall, taking care to screw into the wall studs that you marked in step #4.
  7. Put a bead of caulk along the top of the vanity base to hold the countertop in place. Carefully set in the new countertop.
  8. Reconnect the plumbing that you disconnected as part of step #1.
  9. Put down a thin bead of caulk along the edges of the countertop below the lip. Smooth the caulk in place with a damp rag.

Now your new vanity is all set. Allow the caulk to dry before getting moisture near it, and don’t forget to turn the water supply back on! If you run into any problems, don’t hesitate to call your local Murphy plumber!

Tags: , , , , , , ,
Posted in Plumbing | Comments Off

Harris Ranch Plumbing Tip: How to Increase Your Water Pressure

Friday, January 6th, 2012

It’s no fun when you are in the middle of taking a shower in your Harris Ranch home and the stream of water slows to a trickle. The most logical thing to blame the loss of water pressure is a toilet being flushed or a washing machine being filled. It is not uncommon for losses in water pressure to be associated with simultaneous water usage in other parts of the home.

But if low water pressure seems to be a constant problem when only one source is being used and there are no other appliances using water at the same time, you may have a bigger problem on your hands.

The first thing to do is to check the source of the water supply to your outdoor faucets. Turn the hose bibs to the fully open position and run the water. Is the pressure okay? If so, you probably have a problem indoors. While you are outside, check for any leaks in the hose bibs or faucets. A leak can cause a loss of water pressure in other plumbing circuits.

Now check the hose bibs on the lines leading to interior fittings, like faucets or showerheads, etc. Is the hose bib turned to the fully open position? Someone may have been playing with the bib and turned it down or off. If that checks out okay, take a look at all of the fittings in your plumbing fixtures. Are there any leaks? Is there standing water anywhere, indicating a leak?

If so, tighten up the affected fittings. If you need to remove any fittings to inspect or replace (i.e. a worn out washer or bushing), make sure you turn off the water supply to the fitting first.

If there are filter screens in your faucets check them for an accumulation of debris and clean if necessary. A clogged screen can greatly reduce water pressure.

Many new homes now come with a pressure regulator, which governs the water pressure going into the home. The regulator is located above ground, usually where the pipes enter the home. The pressures are usually preset by the regulator manufacturer but may not always be compatible to the local environment. If you think that may be the problem, contact a local plumbing professional for an opinion.

A disruption in the piping that feeds water into the home can also affect water pressure, such as tree roots in the pipes or a break in the line. These problems can only be diagnosed and corrected by qualified Harris Ranch plumbing professionals. Please do not attempt to find and fix these problems as the result may be costly or even dangerous to your health.

Low water pressure can be a drag but it may also only require a quick fix.

Tags: , , , , ,
Posted in Plumbing | Comments Off

What is a Downflow vs. an Upflow Furnace? A Question from Middleton

Wednesday, November 9th, 2011

When you go looking to buy a furnace in Middleton, you may well be surprised by how many different elements go into making a good purchasing decision. There are simply so many different kinds of furnaces available now and they each are more appropriate for certain situations. That means that finding the one that’s right for you is less about finding the one best unit than it is about finding the one that is the best match for your particular circumstances.

This applies to the type of fuel the furnace uses, its energy efficiency, and whether it’s an upflow furnace or a downflow furnace. Energy efficiency and fuel types are probably things that you’re more or less familiar with. But what are we talking about when we classify a furnace as an upflow or downflow model?

Well, it’s pretty much what it sounds like. These terms refer to the direction the air flows as it is taken in and heated by the furnace. So in an upflow furnace, the cool air is taken in at the bottom, warmed, and then expelled at the top. A downflow furnace, on the other hand, takes in cool air at the top and expels heated air at the bottom.

While this is all very exciting, it may still not be obvious what impact this will have on your decision about what type of furnace to buy. The main thing you’ll have to think about when you’re deciding between an upflow and a downflow furnace is where the furnace will be placed in your house.

An upflow furnace is generally installed in the basement so that the heated air is directed towards the parts of the house you want cooled and so that the furnace can be appropriately vented outside of the house. On the other hand, a downflow furnace would be installed in your attic for the same reasons.

So where you want to have the furnace installed is probably the biggest thing to take into account as you’re comparing these two types of equipment. Of course, whether you pick an upflow or a downflow furnace, you’ll still have to select the appropriate AFUE, size and fuel source to best meet your needs. But making the choice between upflow and downflow can at least make it easier to narrow down your options. If you have any questions about which type of furnace is right for your home, talk to your local contractor.

Tags: , , , , ,
Posted in Heating | Comments Off

No Heat in the House? Things to Check and Do: A Tip from Bowmont

Wednesday, October 26th, 2011

In general, when your heating system stops working, you’ll need to call a Bowmont professional to come out and take a look. However, before you do that, there are likely a couple of things you can check on your own to ensure that there really is a problem with the system itself.

For instance, if it’s cold in your house and your heat isn’t coming on, check to make sure that the thermostat is set to a high enough temperature that the heating system would be triggered. Particularly if this is the first really cold day of the season, it’s entirely possible that your thermostat was turned down at some point and left there. And if the thermostat isn’t turned up high enough, the heat will never come on.

Also, it’s worth just taking a second to check and make sure that the power switch on the heating system itself is actually in the proper on position. For the most part, there would be no reason for you to turn this off, but it’s always possible it could have happened in any number of ways and it only takes a second to check.

Depending on the type of fuel source your heating system uses, it’s probably a good idea to check to make sure the supply is still available as well. If you use natural gas, check to make sure that the gas line is open, but don’t try to repair it yourself if it seems to be compromised. If you find something like that, be sure to call your gas company right away.

However, if you use oil as a heat source, take a quick peek at the levels in your tank. There’s always the possibility that you used more than you thought you did or that a delivery was missed for some reason and so your heating system simply has no fuel to run on. Similarly, if your heating system runs on electricity, make sure that the fuse wasn’t blown or that it’s not just too loose to provide an adequate power supply.

If you’ve covered all of these basic troubleshooting bases, it may be time to take a closer look at the heating system itself. On just about every type of system there should be some type of reset switch or button. Follow the instructions to press this button and engage the reset process, but be sure to only try this once. If that resetting doesn’t work, it’s time to back off and call in some professional help.

Tags: , , , ,
Posted in Heating | Comments Off

Furnaces vs. Heat Pumps: A Tip from Fruitland

Monday, October 10th, 2011

If you’re preparing to replace your existing heating system in Fruitland, you may very well be struggling with the question of whether to go with a furnace or a heat pump for all of your future home heating needs. Each of these systems have their own advantages and drawbacks, and once you’ve narrowed it down to one type or the other, you’ll still have a pretty wide variety of products to choose from.

Furnaces are still the most popular type of home heating equipment on the market. You can get furnaces that run on gas, oil or electricity, although gas furnaces are by far the most common type of furnace around these days. The latest models are extremely energy efficient, with AFUE ratings reaching into the high 90%s.

Like heat pumps, furnaces use ducts to transfer heated air throughout your home. They typically require regular maintenance once every year or two depending on the type of furnace you have, and they can be expected to last anywhere from 15 to 25 years when properly maintained. Most modern furnaces are also made to be compatible with a central air conditioning or cooling system as well.

Heat pumps, on the other hand, don’t generate the heat that they circulate throughout your house. Instead they are able to extract the heat from the air outside and pump it inside. This means that they use much less energy than even the most energy efficient furnaces.

However, heat pumps are only capable of heating your house comfortably when the outside temperature is above freezing. If you live in an area with particularly long and frigid winters, you’ll probably find that you need to supplement your heat pump with another heat source. Because of this, it actually makes little sense to use a heat pump in more extreme climates.

On the other hand, if you live in an area with relatively mild winters, heat pumps can be a great option. They provide a constant flow of warm air to all parts of your home and can also keep you house cool during hot summer months. To cool your home, heat pumps simply reverse the process they use to warm it. They take the heat out of your indoor air and pump it outside. This is a very effective home cooling method and makes heat pumps a great solution for year round comfort.

Tags: , , , , , , ,
Posted in Heat Pumps, Heating | Comments Off